Aspects TPUW70050LWH Guia de Instalação descarregar pdf

Wall Pack

Model: 326914

& TPUW70050LWH

1 of 1

Limited Factory Warranty

American Fluorescent Corporation warrants this fixture is free from defects in materials a

for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of de

not cover failure d

ue to improper installation, misuse, mishandling or damage incurred in transit

Safety Precautions

Read all safety precautions and installation instructions carefully before

installing or servicing this fixture. Failure to comply with

instructions could result in potentially fatal electric shock and/or

property damage.

It is recommended that a qualified

fixture must be wired in accordance with all national and local

electrical codes.

Do not

handle any energized fixture or attempt to energize any fixture

with wet hands or while standing on a wet or damp surface or in water.

ASSEMBLY INSTRUCTIONS

Preparing for installation

Disconnect electrical power

Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not

misplace any of the screws or parts which are needed for installing the fixture.

2. Wiring-

all wiring must take place insid

Caution:

Make sure power is off at fuse or circuit breaker box. Check power wires for damage or scrapes. If power supply

wires are within three inches of

Note:

Most dwellings built before 1985 have supply wire rated to 60C. Consult a qualified electrician before installing.

A. Secure gem bar (1) on the

junction box (not

with two screws (3)

(supplied).

B. Make all wire connections

to appropriate wire. Secure

with wire nuts (supplied).

C. Connect the green wires from the fixture and power

source to the green screw on the gem bar (

The black wire from the fixture is connected to the

black wire from power source.

The white wire from the fixture is connected to the

white (neutral) wire from power source.

Tuck all connections neatly into junction box.

3. Mounting

A. Thread nut (2) on stem (4)

stem in the gem bar so

that approx.

the necessary length with nut (2).

B. Install back panel (5)

over stem

the thumbnut (6).

4. Shade-To install the lens (7

)

diffuser with the four

holes on the top and the bottom of

the backpan. Secure lens with

four

. Restore power at fuse or circuit breaker box.

& TPUW70050LWH

American Fluorescent Corporation warrants this fixture is free from defects in materials a

nd workmanship when installed and used under normal operating conditions

for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of de

ue to improper installation, misuse, mishandling or damage incurred in transit

Safety Precautions

Read all safety precautions and installation instructions carefully before

installing or servicing this fixture. Failure to comply with

these

instructions could result in potentially fatal electric shock and/or

It is recommended that a qualified

electrician perform all wiring. This

fixture must be wired in accordance with all national and local

handle any energized fixture or attempt to energize any fixture

with wet hands or while standing on a wet or damp surface or in water.

ASSEMBLY INSTRUCTIONS

Preparing for installation

Disconnect electrical power

at fuse or circuit breaker box before installing or servicing any part of this fixture.

Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not

misplace any of the screws or parts which are needed for installing the fixture.

all wiring must take place insid

e junction box.

Make sure power is off at fuse or circuit breaker box. Check power wires for damage or scrapes. If power supply

wires are within three inches of

the ballast power supply

, use wire suitable for at least

Most dwellings built before 1985 have supply wire rated to 60C. Consult a qualified electrician before installing.

junction box (not

supplied)

(supplied).

to appropriate wire. Secure

C. Connect the green wires from the fixture and power

source to the green screw on the gem bar (

1).

The black wire from the fixture is connected to the

The white wire from the fixture is connected to the

white (neutral) wire from power source.

Tuck all connections neatly into junction box.

Adjust the length of the

that approx.

7/8” is exposed. Secure

the necessary length with nut (2).

over stem

(4) and secure it with

)

align the four holes on the

holes on the top and the bottom of

four

screws (8).

. Restore power at fuse or circuit breaker box.

LED Wall Sconce

120VAC / 60Hz

nd workmanship when installed and used under normal operating conditions

for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of de

fective fixture or components; it does

ue to improper installation, misuse, mishandling or damage incurred in transit

This fixture is designed for use in a 110

Do not use on a dimming circuit.

To reduce the

risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding, there must be a separate ground wire (green)

between

this fixture and the ground connection of your main power

supply panel.

This fixture is intended to be used for general

damp locations only.

at fuse or circuit breaker box before installing or servicing any part of this fixture.

Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not

misplace any of the screws or parts which are needed for installing the fixture.

Make sure power is off at fuse or circuit breaker box. Check power wires for damage or scrapes. If power supply

, use wire suitable for at least

90C (194F).

Most dwellings built before 1985 have supply wire rated to 60C. Consult a qualified electrician before installing.

LED Wall Sconce

120VAC / 60Hz

8060663 R2

nd workmanship when installed and used under normal operating conditions

fective fixture or components; it does

120VAC, 60Hz fused circuit.

risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding, there must be a separate ground wire (green)

contact

this fixture and the ground connection of your main power

This fixture is intended to be used for general

outdoor lighting in dry or

at fuse or circuit breaker box before installing or servicing any part of this fixture.

Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not

Make sure power is off at fuse or circuit breaker box. Check power wires for damage or scrapes. If power supply

Most dwellings built before 1985 have supply wire rated to 60C. Consult a qualified electrician before installing.

Wall Pack 1

Resumo do Conteúdo

Página 1 - Wall Pack

Wall Pack Model: 326914 & TPUW70050LWH 1 of 1 Limited Factory Warranty American Fluorescent Corporation warrants this fixture is free from

Comentários a estes Manuais

Sem comentários

Aspects TPUW70050LWH Guia de Instalação

Consulte online ou descarregue Guia de Instalação para não Aspects TPUW70050LWH. Aspects TPUW70050LWH Installation Guide Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com não Aspects TPUW70050LWH